Tektronix
Tektronix TCP0030A AC/DC Current Probe 30 A 120 MHz TekVPI | Probe Arus
TCP0030A is a high-performance, easy-to-use AC/DC current probe designed for use and direct connection to oscilloscopes with the TekVPI™ probe interface.
TCP0030A is a high-performance, easy-to-use AC/DC current probe designed for use and direct connection to oscilloscopes with the TekVPI™ probe interface. This AC/DC current measurement probe provides greater than 120 MHz of bandwidth with selectable 5 A and 30 A measurement ranges. It also provides exceptional low-current measurement capability and accuracy to current levels as low as 1 mA, important for meeting today’s challenging current measurement needs.
Key Features
- Easy-to-use and accurate AC/DC current measurements
- Intelligent communication with TekVPI™ oscilloscopes provides: – Units scaling and readout. Automatic, on-screen readout of amps and magnitude. Manual setup is not required. Hand calculation from volts to amps is unnecessary
- Intelligent communication with TekVPI™ oscilloscopes provides: – Push button degauss and Autozero functionality
- Intelligent communication with TekVPI™ oscilloscopes provides: – Probe status and diagnostic indicator LEDs
- Intelligent communication with TekVPI™ oscilloscopes provides: – Remote GPIB/USB probe control
- Split-core construction allows easy circuit connection
- High accuracy with typically less than 1% DC gain error
- Low noise and DC drift
- 3rd party safety certification
Spesifikasi
| Electrical characteristics | |
|---|---|
| Bandwidth | DC to ≥120 MHz |
| Rise time | ≤2.92 ns |
| Maximum DC current | 30 A |
| Maximum RMS current | 30 A |
| Maximum peak pulse current | 50 A |
| Maximum bare wire voltage | 150 V CAT II, (insulated wire 300 V CAT II) |
| Sensitivity | 1 mA (on oscilloscopes that support 1 mV/div setting) |
| DC accuracy | ±3% warranted |
| Accuracy, typical | DC: ±1% of reading; DC to 60 Hz, ≤5 A: ±1%; 60 Hz – 5 kHz, ≤5 A: ±1.5%; DC – 5 kHz, >5 A: ±1.5% |
| Maximum Amp-Second product | 500 A*µs (in 30 A range) |
| Insertion impedance | 1 mΩ at 10 kHz; 3.5 mΩ at 100 kHz; 0.08 Ω at 1 MHz; 0.15 Ω at 10 MHz; 0.7 Ω at 100 MHz; 0.85 Ω at 120 MHz |
| Signal delay | 14.5 ns |
| Current ranges | 5 A and 30 A |
| Power requirements | TCP0030A is powered directly by oscilloscopes with the TekVPI™ interface. Note: For best support, download and install the latest version of the oscilloscope software from www.tek.com. |
| Physical characteristics | |
| Probe head, Length | 20 cm (7.77 in) |
| Probe head, Width | 1.6 cm (0.625 in) |
| Probe head, Height | 3.2 cm (1.25 in) |
| Maximum conductor size | 5 mm (0.197 in) |
| Cable length | 200 cm (79 in) |
| Shipping weight | 1.55 kg (3.44 lb) |
| EMC environment and safety | |
| Temperature, Operating | 0 °C to 50 °C (32 °F to 122 °F) |
| Temperature, Nonoperating | -40 °C to +75 °C (-40 °F to 167 °F) |
| Humidity, Operating | 5% to 95% Relative Humidity (RH) at up to +30 °C; 5% to 85% RH above 30 °C up to +50 °C, noncondensing |
| Humidity, Nonoperating | 5% to 95% Relative Humidity (RH) at up to +30 °C; 5% to 85% RH above 30 °C up to +75 °C, noncondensing |
| Altitude, Operating | Up to 3,000 m (10,000 ft.) |
| Altitude, Nonoperating | Up to 12,192 m (40,000 ft.) |
| Compliance labeling | CE (European Union), WEEE (European Union) |
Aplikasi
Power supplies
Semiconductor devices
Power inverters/converters
Electronic ballasts
Industrial/consumer electronics
Mobile communications
Motor drives
Transportation systems
Unduhan & Sumber
Butuh konsultasi teknis?
Kirim kebutuhan pengujian Anda — tim Terastek membantu menentukan konfigurasi yang sesuai.
